With the continuous evolution of Ethernet networks, many network devices still require compatibility between different Ethernet speeds. A common challenge is connecting a 1000BASE interface to a 100BASE interface.
The C-LIGHT SGMII 1000BASE to 100BASE SFP optical module provides an efficient solution by integrating SGMII rate gear, protocol conversion, and optical transmission functions into a compact optical transceiver. It enables Gigabit Ethernet interfaces to communicate with Fast Ethernet optical networks while maintaining stable data transmission.
This technology plays an important role in industrial Ethernet, telecom access networks, embedded systems, and legacy network upgrades. SGMII is a serial interface technology that can support 10Mbps, 100Mbps, and 1Gbps Ethernet operation through rate adaptation.
The SGMII 1000BASE to 100BASE optical module is a special optical transceiver designed to convert Ethernet signals between different speeds.
Unlike traditional optical modules that only perform electrical-optical conversion, this type of module integrates Ethernet processing functions to achieve:
1000Mbps SGMII interface compatibility
100Mbps optical transmission
Ethernet frame rate adaptation
Protocol conversion between different Ethernet standards
The module allows a Gigabit switch port to connect with a 100Mbps fiber network without replacing existing network equipment.
Many existing networks contain mixed-speed devices. For example:
New switches supporting 1000BASE SGMII interfaces
Legacy devices using 100BASE-FX optical interfaces
Industrial equipment requiring long-term operation
Direct connection between different Ethernet speeds is usually impossible because 1000BASE-X and 100BASE-FX use different physical layer standards.
The SGMII optical module solves this problem by providing intelligent speed adaptation between the two standards.
Replacing complete network systems can be expensive and time-consuming. SGMII 1000BASE to 100BASE optical modules allow customers to upgrade network equipment while maintaining existing fiber infrastructure.
Industrial systems often use 100Mbps Ethernet because of long product lifecycles and stable performance requirements.
The conversion optical module provides a practical solution for connecting modern controllers with older fiber networks.
The internal structure of the conversion optical module mainly includes:
SGMII electrical interface
SerDes conversion circuit
Ethernet MAC/PHY processing unit
Rate adaptation logic
Optical transmitter and receiver
The basic signal path is:
1000BASE SGMII Electrical Signal
Ethernet Rate Conversion Processing
100BASE-FX Optical Signal
Fiber Transmission
SGMII uses serial differential signaling and typically operates at a 1.25Gbps line rate while supporting multiple Ethernet speeds through adaptation. This reduces PCB complexity and allows compact network designs.
When operating at 100Mbps, the SGMII adaptation logic adjusts the data stream to match the lower Ethernet rate. The system maintains a Gigabit-speed internal interface while performing data repetition and rate conversion.
The module must handle differences between 1000BASE-X and 100BASE-FX transmission formats.
The conversion process includes:
Receiving Ethernet frames from the SGMII interface
Analyzing speed and protocol information
Adjusting encoding and timing
Sending converted frames through the optical interface
SerDes (Serializer/Deserializer) technology converts parallel Ethernet data into high-speed serial signals and performs the reverse operation during reception.
The integrated PHY manages communication between different Ethernet speeds.
Main functions include:
Speed negotiation
Signal regeneration
Clock recovery
Data synchronization
After Ethernet processing, the optical engine converts electrical signals into optical signals.
Typical optical components include:
1310nm FP laser
PIN receiver
Single-mode fiber interface
LC Simplex or Duplex optical connector
| Parameter | Specification |
|---|---|
| Host Interface | SGMII |
| Electrical Speed | 1000Mbps |
| Optical Speed | 100Mbps |
| Ethernet Standard | 100BASE-FX |
| Wavelength | 1310nm |
| Fiber Type | Single Mode Fiber |
| Connector | LC Duplex |
| Package | SFP |
| Transmission Distance | Up to 60km or customized |
Industrial equipment often requires long service life and stable communication. These modules enable modern Ethernet switches to connect with existing 100Mbps optical systems.
Telecom operators often have mixed-generation infrastructure. Rate-conversion optical modules help integrate new equipment with existing fiber networks.
Video surveillance and monitoring systems may contain different generations of Ethernet equipment.
The conversion module provides reliable fiber connectivity between Gigabit network equipment and Fast Ethernet terminals.
Factories and automation systems usually prioritize stability over maximum bandwidth.
100BASE optical networks remain widely used in many industrial environments.
High Compatibility: Supports connection between different Ethernet generations.
Network Upgrade Friendly: Avoids replacing existing fiber infrastructure.
Reliable Transmission: Provides stable fiber communication.
Flexible Deployment: Suitable for industrial and telecom environments.
Although modern data centers are moving toward 400G, 800G, and 1.6T optical networks, Ethernet conversion modules remain important in industrial and access networks.
Future C-LIGHT possible multi-rate transceivers include:
50G/25G/10G multi-rate SFPs
OTU4/100G/40G multi-rate QSFPs
800G/400G/200G/100G DCO OSFPs / QSFP-DD
The SGMII 1000BASE to 100BASE optical module provides an effective solution for connecting different generations of Ethernet networks.
By integrating SerDes, PHY processing, rate adaptation, and optical conversion technologies, it enables reliable communication between Gigabit Ethernet equipment and Fast Ethernet optical systems.
For industrial networks, telecom systems, and legacy infrastructure upgrades, this type of optical module remains a valuable and practical connectivity solution.
Answer: It is an optical transceiver that converts a 1000Mbps SGMII electrical interface into a 100Mbps optical Ethernet connection.
Answer: Many networks contain different generations of Ethernet equipment. Speed conversion enables compatibility without replacing existing systems.
Answer: The module uses SerDes, PHY processing, Ethernet rate adaptation, and optical conversion technologies.
Answer: Typical designs support 100BASE-FX optical interfaces using single-mode fiber and LC connectors.
Answer: They are widely used in industrial Ethernet, telecom access networks, monitoring systems, and legacy network upgrades.
Answer: 1000BASE-X operates at Gigabit Ethernet speed, while 100BASE-FX is a Fast Ethernet optical standard operating at 100Mbps.
Answer: Yes. C-LIGHT provides customized optical transceiver solutions for industrial Ethernet, telecom, and special communication applications.
For any questions, please contact us by email or WhatsApp.
Email: sales@c-light.com
WhatsApp: +86 132 6656 7067
